PV Logic Flexi Kit 80w & 10Ah Charge Controller
£320.00
Out of stock
Product Number
3070185
The range of PV Logic FLEXi solar panels are robust, low profile and lightweight and are ideal for use where the substrate to which the panel will be fixed has a slight curve. Panels are available in sizes from 10w to 120w.
Specifications:
Power (Wp) 80watts
Nominal Voltage (Vmp) 18V DC
Nominal Current (Imp) 4.45A
Open Circuit Voltage (Voc) 21.6V
Short Circuit Current (Isc) 4.82A
Operating Temperature -40 to + 80 Deg C
Max System Voltage 750V DC
Dimensions 885x665x3mm (Junction box 10mm)
Weight 4Kg
Approx. watt-hours/day** 480W
Approx. amp-hours/day** 26.7A
** Based on 6 hours of average daily peak sunlight hours
Contents
1 x STPVF080. 80wp solar panel
1 x 4m Cable (attached)
1 x Fuse
6 x Ring Terminals
1 x Instruction Sheet
Self-healing top surface
The ETFE top layer gives the PV Logic Flexi extra resilience in really tough conditions.
ETFE has a memory effect or self-healing capacity in the event the panel comes into
contact with branches etc, thus ensuring any slight abrasions are ‘healed’ within a few hours.
The Flexi range can even be walked on with soft deck shoes! During production the ETFE is
dimpled to further protect the panel and provide an anti-slip surface, particularly useful
if the panel is fitted to a boat deck.
Completely waterproof
Each panel is assembled to ensure complete encapsulation. This ensures the 6 layer heavy
duty laminate protects the solar cell circuit from extreme conditions. The junction box
is also injected with special silicon, guaranteeing no water ingress.
Cells protected from hot spots.
Where used on a camper van or boat, partial shading of a solar panel is typical. In these
circumstances, heat build-up and damaging hot spots can occur leading to a significantly
reduced life cycle of the panel. The larger 60w and 80w PV Logic Flexi panels have up to
two shading diodes housed within the fully waterproof junction box to prevent this occurrence.
Superior design
There are no square edges on a PV Logic Flexi! Rounded panel corners and a unique curved junction
box provide superior adhesion, no snag lamination and no sharp edges. The junction box is
mechanically fixed in addition to being bonded to the panel. Strain relief is provided for the
fitted 4m UV stabilised PV cable ensuring it cannot be accidentally pulled from the junction box.
Easy fix
The Flexi range can be bonded to flat or slight curved surfaces (3cm curve per metre) such as
painted aluminium, metal, GRP and fibreglass using Simson ISR 70-03. The aluminium layer is also
pre-drilled with 4.5mm holes should the panel need to be mechanically fixed as well as or instead of bonding.
Specifications:
Power (Wp) 80watts
Nominal Voltage (Vmp) 18V DC
Nominal Current (Imp) 4.45A
Open Circuit Voltage (Voc) 21.6V
Short Circuit Current (Isc) 4.82A
Operating Temperature -40 to + 80 Deg C
Max System Voltage 750V DC
Dimensions 885x665x3mm (Junction box 10mm)
Weight 4Kg
Approx. watt-hours/day** 480W
Approx. amp-hours/day** 26.7A
** Based on 6 hours of average daily peak sunlight hours
Contents
1 x STPVF080. 80wp solar panel
1 x 4m Cable (attached)
1 x Fuse
6 x Ring Terminals
1 x Instruction Sheet
Self-healing top surface
The ETFE top layer gives the PV Logic Flexi extra resilience in really tough conditions.
ETFE has a memory effect or self-healing capacity in the event the panel comes into
contact with branches etc, thus ensuring any slight abrasions are ‘healed’ within a few hours.
The Flexi range can even be walked on with soft deck shoes! During production the ETFE is
dimpled to further protect the panel and provide an anti-slip surface, particularly useful
if the panel is fitted to a boat deck.
Completely waterproof
Each panel is assembled to ensure complete encapsulation. This ensures the 6 layer heavy
duty laminate protects the solar cell circuit from extreme conditions. The junction box
is also injected with special silicon, guaranteeing no water ingress.
Cells protected from hot spots.
Where used on a camper van or boat, partial shading of a solar panel is typical. In these
circumstances, heat build-up and damaging hot spots can occur leading to a significantly
reduced life cycle of the panel. The larger 60w and 80w PV Logic Flexi panels have up to
two shading diodes housed within the fully waterproof junction box to prevent this occurrence.
Superior design
There are no square edges on a PV Logic Flexi! Rounded panel corners and a unique curved junction
box provide superior adhesion, no snag lamination and no sharp edges. The junction box is
mechanically fixed in addition to being bonded to the panel. Strain relief is provided for the
fitted 4m UV stabilised PV cable ensuring it cannot be accidentally pulled from the junction box.
Easy fix
The Flexi range can be bonded to flat or slight curved surfaces (3cm curve per metre) such as
painted aluminium, metal, GRP and fibreglass using Simson ISR 70-03. The aluminium layer is also
pre-drilled with 4.5mm holes should the panel need to be mechanically fixed as well as or instead of bonding.
Write Your Own Review